Omron Automation
BDT 12000
Omron PLC
Class 1: INTRODUCTION AND UNDERSTANDING OF SWITCHING CONTACTS- NO/NC DEVICES
Class 2 : INTRODUCTION TO VARIOUS TYPES OF SENSORS
Class 3 : LOAD CONTROLLING USING VARIOUS TYPES OF SENSORS
Class 4 : SPECIFICATION, SELECTION & CONNECTION DIAGRAM OF MAGNETIC CONTACTOR
Class 5 : LOAD CONTROLLING USING PRACTICAL PRACTICE USING MAGNETIC CONTACTOR
Class 6: SPECIFICATION, SELECTION & CONNECTION DIAGRAM OF MAGNETIC RELAY
Class 7: LOAD CONTROLLING CIRCUIT PRACTICAL PRACTICE BY USING MAGNETIC RELAY
Class 8: SPECIFICATION, SELECTION & CONNECTION DIAGRAM OF ON DELAY TIMER
Class 9: LOAD CONTROL CIRCUIT PRACTICAL PRACTICE BY USING ON DELAY TIMER
Class 10: SPECIFICATION, SELECTION & CONNECTION OF OFF DELAY TIMER
Class 11: LOAD CONTROL CIRCUIT PRACTICAL PRACTICE BY USING OFF DELAY TIMER
Class 12: SPECIFICATION , SELECTION & CONNECTION DIAGRAM OF TWIN TIMER/ SEQUENTIAL TIMER
Class 13: LOAD CONTROL CIRCUIT PRACTICAL PRACTICE BY USING TWIN TIMER / SEQUENTIAL TIMER
Class 14: INTRODUCTION TO PLC AUTOMATION
Class 15: DISCUSS ABOUT PLC INPUT ELEMENT
Class 16: DISCUSS ABOUT PLC OUTPUT ELEMENT
Class 17: DISCUSS ABOUT PLC INPUT MODULE/OUTPUT MODULE
Class 18: DISCUSS ABOUT PLC ADDRESSING
Class 19: FAMILIARIZATION WITH VARIOUS PLC LANGUAGES
Class 20: BLOCK DIAGRAM OF PLC
Class 21: CONCEPT ABOUT LADDER
Class 22: BASIC CONCEPT OF PLC SOFTWARE & DATA CABLE
Class 23: OVERVIEW & INSTALLATION OF CX PROGRAMMER
Class 24: FAMILIARIZATION WITH VARIOUS LADDER SYMBOL
Class 25: LOAD CONTROLLING WITHOUT LATCHING CIRCUIT PRACTICAL PRACTICE
Class 26: LOAD CONTROLLING WITH LATCHING PRACTICAL PRACTICE
Class 27: INTRODUCTION TO SET-RESET COMMAND
Class 28: LOAD CONTROLLING USING SET RESET COMMAND
Class 29: INTRODUCTION TO ZONE RESET COMMAND
Class 30: FAMILIARIZATION WITH INTERNAL AUXILIARY RELAY IN PLC
Class 31: COMPARISON BETWEEN GENERAL AUXILIARY RELAY AND BATTERY BACKED AUXILIARY RELAY
Class 32: FAMILIARIZATION WITH DIFFERENT TYPE OF INTERNAL TIMERS IN PLC
Class 33: COUNTING SYSTEM AND LOGIC OF INTERNAL ON DELAY TIMERS IN PLC
Class 34: DIFFERENCE BETWEEN NORMAL TIMERS AND RETENTIVE TIMERS
Class 35: ON DELAY TIMER LOGIC PRACTICAL PRACTICE
Class 36: DESIGNING A TWIN TIMER USING ON DELAY TIMER
Class 37: GENERAL TIMER VS RETENTIVE TIMER PRACTICAL PRACTICE
Class 38: DESIGN OF A COMPLICATED PROJECT USING MULTIPLE TIMERS AS PER REQUIREMENT
Class 39: DESIGN A TRAFFIC CIRCUIT USING MULTIPLE TIMERS
Class 40: FAMILIARIZATION WITH DIFFERENT TYPES OF COUNTERS IN PLC
Class 41: COUNTER COMBINED WITH TIMER & SENSOR PRACTICAL PRACTICE
Class 42: STAR-DELTA CIRCUIT PRACTICAL PRACTICE IN PLC
Class 43: FAMILIARIZATION WITH VARIOUS TYPES OF DATA REGISTERS IN PLC
Class 44: PROGRAMMING OF DATA REGISTERS COMBINED WITH INCREMENT, DECREMENT & DATA REGISTERS
Class 45: TIMER COMBINED WITH DATA REGISTER PROGRAMMING PRACTICE
Class 46:COUNTERS COMBINED WITH DATA REGISTER PROGRAMMING PRACTICE
Class 47: FAMILIARIZATION WITH ARITHMETIC COMMANDS
Class 48: PROGRAMMING PRACTICE USING ARITHMETIC COMMANDS
Class 49: INTRODUCTION TO “COMPARISON” COMMAND IN PLC
Class 50: INTRODUCTION TO “MOV “COMMAND
Class 51: PROGRAMMING PRACTICE USING COMPARISON COMMAND
Class 52: PROGRAMMING PRACTICE USING MOV COMMAND
Class 53: INTRODUCTION TO “CMP” COMMAND
Class 54: PROGRAMMING PRACTICE USING CMP COMMAND
Class 55: INTRODUCTION AND PROGRAMMING PRACTICE USING “CALL JUMP” COMMAND
Class 56: MOTOR AND PUMP CONTROLLING LOGIC PRACTICAL PRACTICE USING TIMER AND INTERLOCKING CONCEPT
Class 57: LOAD CONTROLLING LOGIC PRACTICAL PRACTICE COMBINED WITH TIMER AND COMPARE COMMAND
Class 58: DESIGN A TRAFFIC LIGHT SIMULATOR BY FOLLOWING A CERTAIN DATA TABLE AND ADVANCED COMMANDS
Class 59: DESIGN A LOGIC TO OPERATE MULTIPLE LOAD USING “COMPARE” & COUNTER COMMAND
Class 60: DESIGN A LOGIC TO MANUPULATE THE OPERATING TIME OF A LOAD USING “MOV” COMMAND
Class 61: DESIGN A LOGIC TO CHANGE THE OPERATING TIME OF A TIMER AS PER OPERATOR’S REQUIREMENT USING “INCREMENT” & “DECREMENT” COMMAND
Class 62: PROGRAM READ/WRITE PROCESS USING DATA CABLE
Class 63: ONLINE MONITORING & TROUBLE SHOOTING PROCESS FROM PC/LAPTOP PRACTICAL PRACTICE
Class 64: PROCESS OF CONTROLLING AC LOAD USING DC SUPPLY OR CONTROLLING DC LOAD USING AC SUPPLY PRACTICA PRACTICE
Class 65: POWER SUPPLY & WIRING OF INPUTS PRACTICAL PRACTICE
Class 66: WIRING OF OUTPUTS PRACTICAL PRACTICE
Omron VFD/ Frequency Inverter Programming, Connection, Motor Run, Troubleshooting
Class 1: EVERYTHING ABOUT VFD
Class 2: SPECIFICATION, SELECTION AND CONNECTION PROCEDURE OF THREE PHASE INDUCTION MOTOR
Class 3: MEASURING PROCEDURE PRACTICAL PRACTICE BY USING MULTIMETER
Class 4: MEASURING PROCEDURE PRACTICAL PRACTICE BY USING CLAMP ON METER
Class 5: MOTOR CHECKING PROCEDURE FROM MULTIMETER
Class 6: STAR CONNECTION PHYSICAL PRACTICE
Class 7: DELTA CONNECTION PHYSICAL PRACTICE
Class 8: VFD HARDWARE DESCRIPTION
Class 9: PRACTICAL CONNECTION OF MOTOR WITH INVERTER
Class 10: INTRODUCTION TO VFD EXTERNAL MODE
Class 11: VFD EXTERNAL MODE WIRING PRACTICAL PRACTICE
Class 12: VFD OPERATION MODE SELECTION
Class 13: VFD PARAMETER SETTING
Class 14: VFD FAULT FINDING AND TROUBLESHOOTING
Omron Human Machine Interface (HMI) Programming, Connection & Load Controlling
Class 1: INTRODUCTION TO HMI – UNDERSTANDING WIRING & INSTALLATION
Class 2: INTRODUCTION TO VARIOUS TYPES OF SWITCH (MOMENTARY, MAINTAINED, SET, RESET ETC.
Class 3: SET/RESET BUTTON FUNCTIONS PRACTICAL PRACTICE
Class 4: INTRODUCTION TO HMI DISPLAY ELEMENTS
Class 5: BUTTON FUNCTIONS-SET CONSTANTS, INCREMENT & DECREMENT & PRACTICAL IMPLEMENTATION ON LOADS
Class 6: INTRODUCTION TO SIMPLE & MULTI STATE INDICATORS IN HMI & LOAD CONTROLLING PRACTICAL PRACTICE
Class 7: INTRODUCTION T0 MULTI STATE BUTTONS IN HMI & LOAD CONTROLLING PRACTICAL PRACTICE
Class 8: INTRODUCTION TO NUMERIC DISPLAY FOR DISPLAYING NUMBER, COUNTS OR PRODUCTION & LOAD CONTROLLING PRACTICAL PRACTICE
Class 9: INTRODUCTION TO NUMERIC ENTRY FOR GIVING THE INPUT FROM HMI & LOAD CONTROLLING PRACTICAL PRACTICE
Class 10: INTRODUCTION TO NUMERIC DISPLAY & GAIN SETTING IN NUMERIC DISPLAY
Class 11: INTRODUCTION TO MOVING SIGN & PRACTICAL IMPLEMENTATION
Class 12: OPERATING AND SETTING OF MULTIPLE SCREENS IN HMI & PRACTICAL IMPLEMENTATION
Class 13: HMI CONNECTION PROCEDURE WITH LAPTOP/COMPUTER