Delta Automation – Multipurpose Engineering & Industrial Automation
01927279281,01703980538,01726716343,01915834327
01927279281
imo icon

01703980538

Delta Automation

BDT 12000

Delta PLC

Class 1: INTRODUCTION AND UNDERSTANDING OF SWITCHING CONTACTS- NO/NC DEVICES

Class 2 : INTRODUCTION TO VARIOUS TYPES OF SENSORS

Class 3 : LOAD CONTROLLING USING VARIOUS TYPES OF SENSORS

Class 4 : SPECIFICATION, SELECTION & CONNECTION DIAGRAM OF MAGNETIC CONTACTOR

Class 5 : LOAD CONTROLLING USING PRACTICAL PRACTICE USING MAGNETIC CONTACTOR

Class 6: SPECIFICATION, SELECTION & CONNECTION DIAGRAM OF MAGNETIC RELAY

Class 7: LOAD CONTROLLING CIRCUIT PRACTICAL PRACTICE BY USING MAGNETIC RELAY

Class 8: SPECIFICATION, SELECTION & CONNECTION DIAGRAM OF ON DELAY TIMER

Class 9: LOAD CONTROL CIRCUIT PRACTICAL PRACTICE BY USING ON DELAY TIMER

Class 10: SPECIFICATION, SELECTION & CONNECTION OF OFF DELAY TIMER

Class 11: LOAD CONTROL CIRCUIT PRACTICAL PRACTICE BY USING OFF DELAY TIMER

Class 12: SPECIFICATION , SELECTION & CONNECTION DIAGRAM OF TWIN TIMER/ SEQUENTIAL TIMER

Class 13: LOAD CONTROL CIRCUIT PRACTICAL PRACTICE BY USING TWIN TIMER / SEQUENTIAL TIMER

Class 14: BASIC CONCEPT OF PLC SOFTWARE DATA CABLE OF DELTA PLC

Class 15: OVERVIEW & INSTALLATION OF SIMATIC STEP 7 FOR WINDOWS 10

Class 16: WIRING PROCESS OF DELTA PLC

Class 17: CLEARING SYNCING AND SOURCING CONCEPT BY USING THE WIRING EXAMPLE OF PNP AND NPN SENSORS

Class 18: LOAD CONTROLLING WITHOUT LATCHING CIRCUIT PRACTICAL PRACTICE IN DELTA PLC

Class 19: LOAD CONTROLLING IN SERIES CIRCUIT PRACTICAL PRACTICE IN DELTA PLC

Class 20: LOAD CONTROLLING IN PARALLEL CIRCUIT PRACTICAL PRACTICE IN DELTA PLC

Class 21: MULTIPLE LOAD CONTROLLING IN PARALLEL CIRCUIT USING ONE SINGLE INPUT PRACTICAL PRACTICE IN DELTA PLC

Class 22: INTRODUCTION TO INTERLOCKING AND LOAD CONTROLLING PRACTICAL PRACTICE IN DELTA PLC

Class 23: CONNECTING SWITCHES IN NO/NC AND CLEARING CONCEPT OF NO/NC PUSH BUTTON CONNECTION PRACTICAL PRACTICE IN DELTA PLC

Class 24: INTERLOCKING OF VARIOUS OUTPUTS USING MULTIPLE INPUTS LOGIC PRACTICAL PRACTICE 1

Class 25: INTERLOCKING OF VARIOUS OUTPUTS USING MULTIPLE INPUTS LOGIC PRACTICAL PRACTICE 2

Class 26: INTRODUCTION TO SET/RESET COMMAND AND LOAD CONTROLLING LOGIC PRACTICAL PRACTICE IN DELTA PLC

Class 27: INTERLOCKING OF VARIOUS OUTPUTS USING MULTIPLE INPUTS COMBINED WITH SET/RESET COMMAND PRACTICAL PRACTICE 1

Class 28: INTERLOCKING OF VARIOUS OUTPUTS USING MULTIPLE INPUTS COMBINED WITH SET/RESET COMMAND PRACTICAL PRACTICE 2

Class 29: INTRODUCTION TO POSITIVE AND NEGATIVE PULSE AND PRACTICAL PRACTICE USING PULSE COMMAND IN DELTA PLC

Class 30: INTRODUCTION TO VARIOUS TYPES OF TIMERS IN DELTA PLC

Class 31: LOAD CONTROLLING USING ON DELAY TIMER PRACTICAL PRACTICE 1

Class 32: MULTIPLE LOAD CONTROLLING USING DELAY TIMER PRACTICAL PRACTICE 2

Class 33: LOAD AUTO ON/OFF CONTROLLING CIRCUIT USING TIMER PRACTICAL PRACTICE 3

Class 34: LOAD AUTO ON/OFF CONTROLLING CIRCUIT USING TIMER PRACTICAL PRACTICE 4

Class 35: TURNING ON/OFF A MOTOR AND PUMP SEQUENTIALLY BY USING TIMER PRACTICAL PRACTICE IN DELTA PLC

Class 36: TURNING ON/OFF A LOAD ONLY BY A GIVEN PERIOD OF TIME ACCORDING TO THE OPERATOR PRACTICAL PRACTICE IN DELTA PLC

Class 37: TURNING ON/OFF A LOAD ONLY BY A GIVEN PERIOD OF TIME ACCORDING TO THE OPERATOR BY SETTING A CERTAIN FREQUENCY AND COMBINING AN ALARM IN THE LOGIC PRACTICAL PRACTICE

Class 38: FAMILIARIZATION WITH COMPARISON COMMANDS COMBINED WITH TIMER LOGIC & LOAD CONTROLLING PRACTICAL PRACTICE 1

Class 39: FAMILIARIZATION WITH COMPARISON COMMANDS COMBINED WITH TIMER LOGIC & LOAD CONTROLLING PRACTICAL PRACTICE 2

Class 40: FAMILIARIZATION WITH COMPARISON COMMANDS COMBINED WITH TIMER LOGIC & LOAD CONTROLLING PRACTICAL PRACTICE 3

Class 41: FAMILIARIZATION WITH COMPARISON COMMANDS COMBINED WITH TIMER LOGIC & LOAD CONTROLLING PRACTICAL PRACTICE 4

Class 42: DESIGNING A TRAFFIC LIGHT SIMULATOR LOGIC AS PER THE REQUIREMENT OF THE CONSUMER OR THE OPERATOR IN DELTA PLC

Class 43: FAMILIARIZATION WITH COUNTER COMMANDS AND LOAD CONTROLLING PRACTICAL PRACTICE IN DELTA PLC

Class 44: DESIGNING A LOGIC SUCH THAT AFTER CERTAIN PERIOD OF COUNTING LOAD SHOULD BE ON & THE COUNTER SHOULD BE RESET

Class 45: DESIGNING A BOTTLE COUNTING LOGIC USING COUNTER AND SENSOR PRACTICAL PRACTICE IN DELTA PLC

Class 46: FAMILIARIZATION WITH COMPARISON COMMANDS COMBINED WITH TIMER LOGIC & LOAD CONTROLLING PRACTICAL PRACTICE

Class 47: FAMILIARIZATION WITH “MOV” COMMAND AND PREPARE A LOAD CONTROLLING LOGIC BY COMBINING TIMERS IN THE LOGIC IN DELTA PLC

Class 48: DESIGN ANOTHER LOGIC TO CHANGE THE TIME OF THE ABOVE LOGIC USING INCREMENT AND DECREMENT COMMAND

Class 49: DESIGNING A LOGIC TO CONTROL THE RUN TIME OF AN OUTPUT BY VARYING THE TIME OF THE TIMER USING “MOV” COMMAND PRACTICAL PRACTICE IN DELTA PLC

Class 50: FAMILIARIZATION WITH ARITHMETIC COMMANDS IN DELTA PLC

Class 51: DESIGN THE SAME LOGIC AS CLASS 36 BUT TO CHANGE THE TIME USE “INCREMENT” & “DECREMENT” COMMAND

Class 52: FAMILIARIZATION WITH DIFFERENT TYPES OF DATA REGISTERS IN DELTA PLC

Class 53: FAMILIARIZATION WITH “SPECIAL BITS” IN DELTA PLC

Class 54: INTRODUCTION TO “BMOV” COMMAND

Class 55: DESIGN A LOGIC TO MOVE “BLOCK” OF INFORMATION FROM ONE DATA REGISTER TO ANOTHER

Class 56: INTRODUCTION TO “FMOV” COMMAND

Class 57: INTRODUCTION TO “CALL JUMP” COMMAND

Class 58: INTRODUCTION TO “INTERRUPT” COMMAND AND LOAD CONTROLLING PRACTICAL PRATICE

Class 59: INTRODUCTION TO “INVERT” COMMAND

Class 60: INTRODUCTION TO “MASTER CONTROL” COMMAND AND LOAD CONTROLLING PRACTICAL PRACTICE

Class 61: INTRODUCTION TO “PULSE WIDTH MODULATION” COMMAND AND IT’S FEATURES

Class 62: DESIGNING A RETENTIVE TIMER USING DATA REGISTERS IN DELTA PLC

Class 63: INTRODUCTION TO “SEQUENCE COMMAND” AND LOAD CONTROLLING PRACTICAL PRACTICE

Class 64: PROGRAM READ/WRITE PROCESS USING DATA CABLE

Class 65: ONLINE MONITORING & TROUBLE SHOOTING PROCESS FROM PC/LAPTOP PRACTICAL PRACTICE

Class 66: PROCESS OF CONTROLLING AC LOAD USING DC SUPPLY OR CONTROLLING DC LOAD USING AC SUPPLY PRACTICAL PRACTICE

Class 67: POWER SUPPLY & WIRING OF INPUTS PRACTICAL PRACTICE

Class 68: WIRING OF OUTPUTS PRACTICAL PRACTICE

Delta VFD/ Frequency Inverter Programming, Connection, Motor Run, Troubleshooting

Class 1: EVERYTHING ABOUT VFD

Class 2: SPECIFICATION, SELECTION AND CONNECTION PROCEDURE OF THREE PHASE INDUCTION MOTOR

Class 3: MEASURING PROCEDURE PRACTICAL PRACTICE BY USING MULTIMETER

Class 4: MEASURING PROCEDURE PRACTICAL PRACTICE BY USING CLAMP ON METER

Class 5: MOTOR CHECKING PROCEDURE FROM MULTIMETER

Class 6: STAR CONNECTION PHYSICAL PRACTICE

Class 7: DELTA CONNECTION PHYSICAL PRACTICE

Class 8: VFD HARDWARE DESCRIPTION

Class 9: PRACTICAL CONNECTION OF MOTOR WITH INVERTER

Class 10: INTRODUCTION TO VFD EXTERNAL MODE

Class 11: VFD EXTERNAL MODE WIRING PRACTICAL PRACTICE

Class 12: VFD OPERATION MODE SELECTION

Class 13: VFD PARAMETER SETTING

Class 14: VFD FAULT FINDING AND TROUBLESHOOTING

Delta Human Machine Interface (HMI) Programming, Connection & Load Controlling

Class 1: INTRODUCTION TO HMI – UNDERSTANDING WIRING & INSTALLATION

Class 2: INTRODUCTION TO VARIOUS TYPES OF SWITCH (MOMENTARY, MAINTAINED, SET, RESET ETC.

Class 3: SET/RESET BUTTON FUNCTIONS PRACTICAL PRACTICE

Class 4: INTRODUCTION TO HMI DISPLAY ELEMENTS

Class 5: BUTTON FUNCTIONS-SET CONSTANTS, INCREMENT & DECREMENT & PRACTICAL IMPLEMENTATION ON LOADS

Class 6: INTRODUCTION TO SIMPLE & MULTI STATE INDICATORS IN HMI & LOAD CONTROLLING PRACTICAL PRACTICE

Class 7: INTRODUCTION T0 MULTI STATE BUTTONS IN HMI & LOAD CONTROLLING PRACTICAL PRACTICE

Class 8: INTRODUCTION TO NUMERIC DISPLAY FOR DISPLAYING NUMBER, COUNTS OR PRODUCTION & LOAD CONTROLLING PRACTICAL PRACTICE

Class 9: INTRODUCTION TO NUMERIC ENTRY FOR GIVING THE INPUT FROM HMI & LOAD CONTROLLING PRACTICAL PRACTICE

Class 10: INTRODUCTION TO NUMERIC DISPLAY & GAIN SETTING IN NUMERIC DISPLAY

Class 11: INTRODUCTION TO MOVING SIGN & PRACTICAL IMPLEMENTATION

Class 12: OPERATING AND SETTING OF MULTIPLE SCREENS IN HMI & PRACTICAL IMPLEMENTATION

Class 13: HMI CONNECTION PROCEDURE WITH LAPTOP/COMPUTER

Class 14: DATA TRANSFER PROCESS & TROUBLESHOOTING FROM PC/LAPTOP

Ready to get started?

Your class starts when you join! 6 days a week.

8AM – 1PM / 4PM – 8PM, Whenever you like.